BEGINNER'S PLUMBING: WHAT YOU NEED FOR INSTALLING A BATHTUB

Beginner's Plumbing: What You Need for Installing a Bathtub

Beginner's Plumbing: What You Need for Installing a Bathtub

Blog Article

Click Here

Have you been hunting for information on Installing A Bathtub?


How to Install a Bathtub: Install an Acrylic Tub and Tub Surround
Setting up a tub isn't specifically brain surgery, however it does call for strong plumbing, carpentry, as well as sometimes, tiling skills. Changing an old tub with a new one is additionally a moderately challenging job. If the old tub is readily accessible, the project can relocate easily; if you have to open a wall surface to get rid of the old bathtub and position the brand-new bath tub, the job is a lot harder. In either instance, the project is within a home handyman's skills, although you will certainly require an assistant to vacate the old tub as well as set in the new one. Make certain you have actually certified on your own for the task and fit trying it. As opposed to hiring a professional to take control of a halfway-completed project, it is much better to take into consideration employing one before you start. Chances are you might require an expert plumber to make tube links.
This post will certainly help you set up a brand-new bath tub in your bathroom if you have actually currently acquired a brand-new tub and don't need to transform the plan of your previous supply of water pipelines.
Your devices and also product checklist must comprise the following:
  • New Tub
  • Hammer

  • Pipe Wrenches

  • Prybar

  • Safety Glasses

  • Level

  • Pliers

  • Flexible Wrench

  • Putty Blade

  • Screwdriver

  • Cold Knife

  • Tape Measure

  • Pipeline Caps


  • Preparing for the Installment


    First of all, the supporting structure supplied with the bathroom ought to be fitted (if called for) according to the maker's directions. Next off, fit the taps or mixer to the bathtub. When suitable the faucet block, it is important to make certain that if the faucet features a plastic washer, it is fitted between the bath as well as the taps. On a plastic bath, it is also sensible to fit a supporting plate under the taps unit to prevent strain on the bath tub.
    Fit the versatile faucet connectors to the bottom of both faucets making use of 2 nuts and olives (often provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet via the hole in the bathroom. Make use of the nut provided by the producer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
    Next, fit the end of the adaptable overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Ensure you make use of all of the supplied washers.
    Attach the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom must now be ready to be fitted in its last setting.

    Removing Old Touches


    If you require to change old faucets with brand-new ones as a part of your installment, then the first thing you ought to do is detach the water supply. After doing so, turn on the taps to drain any water continuing to be in the system. The process of removing the existing taps can be quite problematic due to the restricted access that is typically the situation.
    Use a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipelines to the faucets. Have a towel prepared for the remaining water that will certainly come from the pipes. Once the supply pipelines have been gotten rid of, make use of the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary taps from transforming throughout this process. As soon as the taps have actually been removed, the holes in the bath/basin will need to be cleaned of any type of old securing compound.
    Before carrying on to fit the brand-new faucets, compare the pipeline links on the old faucets to the brand-new faucets. If the old faucets are longer than the new taps, then a shank adapter is required for the new taps to fit.

    Installing the Bathtub


    Using the two wooden boards under its feet, put the bath tub in the called for placement. The wood boards are helpful in equally spreading the weight of the bathtub over the area of the boards rather than focusing all the weight onto four little factors.
    The following objective is to make sure that the bath tub is leveled all round. This can be achieved by checking the level as well as adjusting the feet on the bath tub till the level checks out level.
    To mount faucets, fit all-time low of the outermost flexible faucet connector to the ideal supply pipe by making a compression sign up with; then do the very same for the other faucet.
    Activate the water supply and also inspect all joints as well as new pipework for leaks and tighten them if required. Load the tub and likewise examine the overflow outlet and also the normal outlet for leakages.
    Finally, take care of the bath paneling as explained in the maker's instruction manual. Tiling as well as sealing around the tub must wait until the bathtub has actually been utilized at least when as this will settle it into its last setting.

    Suitable New Touches


    If the tails of the brand-new taps are plastic, then you will require a plastic port to stop damages to the thread. One end of the connector fits on the plastic tail of the faucet and also the various other end provides a connection to the existent supply pipes.
    If you need to fit a monobloc, then you will certainly need lowering couplers, which links the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
    Next off, place the tap in the installing hole in the bath/basin ensuring that the washers are in place in between the tap as well as the sink. Safeguard the tap in place with the supplier given backnut. Once the tap is firmly in place, the supply pipes can be connected to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with regular faucet adapters. The previous kind must be attached to the tap finishes initially, tightening up only by hand. The supply pipes can later be connected to the other end. Tighten up both ends with a spanner after both ends have actually been linked.

    Tiling Around the Tub


    In the location where the bath fulfills the tile, it is required to seal the joins with a silicone rubber caulking. This is very important as the installation can move sufficient to break a stiff seal, triggering the water to pass through the wall surface between the bathroom and also the tiling, leading to complications with wetness as well as possible leaks to the ceiling below.
    You can choose from a selection of coloured sealers to assimilate your fixtures as well as fittings. They are offered in tubes and also cartridges, as well as are capable of sealing spaces as much as a width of 3mm (1/8 inch). If you have a bigger gap to load, you can load it with twists of drenched newspaper or soft rope. Bear in mind to always fill up the bathtub with water before securing, to permit the movement experienced when the tub remains in use. The sealant can fracture fairly early if you do not consider this activity prior to sealing.
    Additionally, ceramic coving or quadrant ceramic tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are additionally conveniently available on the marketplace. It is recommended to fit the floor tiles making use of waterproof or waterproof sticky and grout.

    How to Install or Replace a Bathtub


    Find Your Dimensions


    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


    Disconnect the Water Supply and Drain Assembly


    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


    Cut Out the Old Tub


    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


    Install the New Tub


    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


    Secure the Tub


    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

    https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


    How to Install a Bathtub

    I am just very curious about A Step-by-Step Guide to Installing a Bathtub and I am hoping you liked the new post. I beg you set aside a second to promote this article if you liked it. Thank you for going through it.


    Excellence? Just call!

    Report this page